Blog về công ty Mingjiada Supply ADI EVAL-ADM2863EEBZ Evaluation Kit, Evaluating The ADM2863E Isolated RS-485 Interface Transceiver

Mingjiada Supply ADI EVAL-ADM2863EEBZ Evaluation Kit, Evaluating The ADM2863E Isolated RS-485 Interface Transceiver

Shenzhen Mingjiada Electronics Co., Ltd. — Long-term supply of the ADI EVAL-ADM2863EEBZ evaluation kit: Simplifies and facilitates the evaluation of the ADM2863E isolated RS-485 interface transceiver. Product details for the EVAL-ADM2863EEBZ evaluation kit are as follows:

Product Parameters:
Model: EVAL-ADM2863EEBZ (Evaluation Kit)
Type: Interface
Function: Digital Isolator
IC/Component Used: ADM2863E
Primary Attribute: Isolation
Contents: Board
EVAL-ADM2863EEBZ Product Image:

The EVAL-ADM2863EEBZ simplifies and facilitates the evaluation of the ADM2863E, a 5.7 kV rms, 500 kbps signal and power isolated, full-duplex RS-485 interface transceiver.

The ADM2863E incorporates an isolated DC-DC converter that supplies power to the isolated side of the EVAL-ADM2863EEBZ evaluation kit without requiring additional ICs.

The EVAL-ADM2863EEBZ incorporates an ADP7104 low-dropout (LDO) regulator that accepts input voltages from 3.3 V to 20 V and regulates them to either 3.3 V or 5 V, supplying the ADM2863E's VCC pin.

Screw-type terminal blocks on the EVAL-ADM2863EEBZ evaluation board connect to the ADM2863E's flexible VIO logic power supply pins. This connection enables the ADM2863E to operate with digital input/output (I/O) voltages ranging from 1.7 V to 5.5 V, facilitating communication with nodes using 1.8 V or 2.5 V power supplies. The VIO pins may alternatively be powered by the ADP7104 regulated power supply.

The EVAL-ADM2863EEBZ provides options for evaluating the ADM2863E within a single system. Digital and RS-485 interface bus signals are readily accessible via screw-type terminal blocks on each evaluation board. Each digital input is configured via on-board jumper options.

Alternative methods may be employed to supply the transmission data input (TxD) signal to the ADM2863E. Each evaluation board incorporates an LTC6900 oscillator, which can be selectively configured to provide a clock signal for the TxD digital input within the 10 kHz to 250 kHz range. For optimal signal integrity, external data signals may be connected using the on-board subminiature A (SMA) connectors.

Equipment required for EVAL-ADM2863EEBZ:
Oscilloscope
Signal generator
3 V to 5.5 V power supply
1.62 V to 5.5 V power supply

EVAL-ADM2863EEBZ Core Chip Details (ADM2863E):
1. Overview:
The ADM2863E features a 5.7 kV RMS, 500 kbps, full-duplex signal with power isolation for RS-485 interface transceivers, offering ±15 kV IEC ESD protection.
2. ADM2863E Product Features:
5.7 kV RMS isolated RS-485 interface/RS-422 transceiver
Low-emission, integrated isolated DC/DC converter
Complies with EN55032 Class B with margin on 2-layer PCB
Intelligent cable reverse polarity protection
Corrects reverse polarity on A, B, Y, and Z bus pins while maintaining full receiver fault-safe functionality
ESD protection on RS-485 interface A, B, Y, and Z pins
≥±12 kV IEC61000-4-2 contact discharge
≥±15 kV IEC61000-4-2 air discharge
High-speed 25 Mbps data rate (ADM2865E/ADM2867E)
Low-speed 500 kbps data rate for EMI control
Compliant with PROFIBUS at 5 V VISO
Wide operating temperature range: −40°C to +105°C
High common-mode transient immunity: 250 kV/μs
Fail-safe operation for short-circuit, open-circuit, and floating input receivers
Supports 196 bus nodes (72 kΩ receiver input impedance)
Full hot-swap controller support (glitch-free power-up/shutdown)

Mingjiada Electronics maintains long-term supply of the [ADI] EVAL-ADM2863EEBZ evaluation kit. For further product details or sample enquiries regarding EVAL-ADM2863EEBZ, please visit Mingjiada Electronics' official website (https://www.integrated-ic.com/) for comprehensive supply information.